Usl JSD-100 Manual User Manual

JSD-100 Manual Cinema Processor USL, Inc. 181 Bonetti Drive San Luis Obispo, CA 93401-7397 USA Phone: +1 805 549 0161

Page 9 5.1LsCL RRs7.1SDDSLc Rc7.1DSLrs RrsLFECL RLFECL RLFELs RsLs RsIn the transition to digital cinema, the industry is adopting new names and

Page 10 4.5 Processing Channels The JSD-100 has 14 “processing channels.” Each of these receives audio from a variety of sources. The “processing c

Page 11 Eight Channel Analog Audio Output (JSD-100x) Eight Channels Balanced 300mV adjustable (L, C, R, Ls, Rs, LFE, Lc/Lrs, Rc/Rrs). Sixteen Chann

Page 12 Processing 96 kHz processing. One-third octave equalization on all channels except LFE, HI, and VI-N. Parametric equalizers on LFE.

Page 13 a three-prong grounding plug and a three-wire power cord to accommodate a safe ground path from the chassis to the electrical system ground.

Page 14 16. 8 Channel Analog Input – Balanced line inputs. Six channels are fixed (L, C, R, LFE, Ls, Rs) and two can be set up as either Lc/Rc or Lr

Page 15 16. 8 Channel Analog Input – Balanced line inputs. Six channels are fixed (L, C, R, LFE, Ls, Rs) and two can be set up as either Lc/Rc or Lr

Page 16 PA Microphone Input. Plug a PA microphone in to the combination XLR / ¼” phone jack. The microphone input may be configured to drive the m

Page 17 RS-232 Interface The RS-232 interface appears on a DE9F connector on the rear panel. The connector is wired as a DCE device. A command inte

Page 18 Unplug the USB cable and proceed to driver installation. USB Driver Installation The JSD-100 Installation (Setup) program creates a subfold

Page 1 Additional JSD-100 Manuals may be viewed / downloaded at: www.uslinc.com

Page 19 7.3 JSD-100 Configuration The JSD-100 is configured using the graphical user interface (Shown in start menu as: JSD-100 Digi

Page 20 Comm Settings Press this button to configure the communications link to the JSD-100. The JSD-100 GUI can communicate with the JSD-100 over Eth

Page 21 US Time Zone UTC Offset Standard Time Abbreviation Daylight Saving Time Abbreviation Hawaii-Aleutian -10:00 HAST HADT Alaska -9:00 AKST AKDT

Page 22 Tabs The remainder of the GUI window contains tabs that divide the remaining configuration data into logical groups. Each tab will be discusse

Page 23 Input Name The name that is shown on the display and logged when a particular format is selected can be set by the user. Type a meaningful nam

Page 24 Decode Option Description L_R The two channel source drives just the left and right speakers. L_C_R The left and right channels of the source

Page 25 EQ Copy Note that the equalizer adjustments adjust the EQ set that is selected for the currently selected format. You can hit the fo

Page 26 Turn off the generator. Copy the equalizer settings to the next channel to be equalized using the Copy button, as described above. Then re

Page 27 Global Tab Global settings, those that do not change with format or EQ set, are set or displayed here. Unit Time The time settings in th

Page 28 the GUI or other devices, etc. Press the Get Latest button to get the 100 most recent log entries. Press the Get All button to get the full l

Page 2 Table of Contents 1. Safety Notice ...

Page 29 terminal area, and then type commands (tab delimited and terminated with a carriage return). See Appendix B for more information on automatio

Page 30 13. Display – indicates the Fader level, format input and bar graph display of the output signal levels. 14. Power Indicator LEDs – displays

Page 31 Adding Groups Create a group for each theater. The group is a collection of JSD-100s, one in each auditorium. Click the “Groups” button at

Page 32 8. JSD-100 Web Interface The JSD-100 includes a web server. The web server can be used to view the current status of the JSD-100, view the

Page 33 The Configuration Page shows the same auditorium data and network data as the status page. When first accessing the configur

Page 34 SNMPv2-SMI::enterprises.38012.4.3.0 = INTEGER: 70 SNMPv2-SMI::enterprises.38012.4.4.0 = INTEGER: 0 SNMPv2-SMI::enterprises.38012.4.5.1.0 = INT

Page 35 JSDV-100 Remote Volume Control The JSDV-100 remote volume control can be installed in an auditorium or other location. It is wired to the JSD

Page 36 Appendix A – Connector Pin Outs Connector Pin Outs For convenience, all connector pin outs are located in this appendix. DB25F AES Input.

Page 37 Channel Number DB25F PINS ( +, -, shield ) Speakers 1 2, 14, 1 Left 2 8, 20, 7 Right 3 5, 17, 4 Center 4 25, 12, 13 LFE 5 23, 10, 22 Ls 6 24,

Page 38 Full Range Audio Channel Biamp Audio Channel Triamp Audio Channel Phoenix Main Output Pins (+, -, shield) DB25M Monitor 1 Output Pins (+, -, s

Page 3 One-Year Limited Warranty USL, Inc. warrants that each product manufactured by it will be free from defects in material and workmanship under

Page 39 Pin Description 1 Control 1. Pulse low to select format 1 (COAX1). Pulses low when format 1 selected. 2 Control 2. Pulse low to select form

Page 40 USL Link The USL Link is an RS485 bus used to interface the JSD-100 to other USL devices such as the JSDV-100 remote volume control

Page 41 Appendix B – Automation Commands These commands are used to query the status of the JSD-100 or change its operation (adjust level, select inp

Page 42 Command Response Description jsd100.sys.mute 1 1 Sets or reads the current mute status of the JSD-100. If the supplied parameter is 1, th

Page 43 Appendix C – System Restore and Power Up Buttons System Restore The JSD-100 has several methods of recovering from an unlikely failure. These

Page 44 JSD-100 Manual Revision History 1. April 2010 – First Edition (preliminary). 2. October 2010 - Second Edition. 3. July 12, 2011 – Third Edi

Page 45 JSD-100x with 8 analog channel output module JSD-100xA with 16 analog channel output module USL, Inc. 181 Bonetti Drive

Page 4 1. Safety Notice Safety Notices Review the following safety precautions to avoid injury and prevent damage to this product. To avoid potent

Page 5 N’opérez pas avec les Échecs Suspects. Si vous suspectez il y a le dégât ou mal fonctionner avec ce produit, appelez l’usine. N’entreprenez

Page 6 Stellen Sie Richtige Belüftung bereit. Die operierend Temperatur sollte zwischen 0° C und 40° C. Die Luftfeuchtigkeit sollte s

Page 7 VDE Certified Power Cords. Pollution: Not intended for environments where conductive pollutants may be present. 2.2 Equipment Class Ty

Page 8 The JSD-100 is “automation friendly.” It features the standard DB25 parallel automation interface, an RS-232 (EIA232) interface